Osaka 96V 10KW Inverter Sine Wave Power JS067-9610K

Model: 96V /10KW
Output rated power: 10000W
Cell voltage DC: 96
Battery voltage range: 80-128V
Battery type: Solar deep cycle lead-acid battery, lithium battery can be set according to the battery

output frequency: 50/601%
Rated input frequency :50Hz /60 Hz 5%
Output voltage
waveform
Consistent with the input voltage waveform.
Power efficiency >85-87%
Charging method PW M
charging current 0A, 5A, 10A, 15A, 20A, 25A, 30A (factory setting 20A)
Automatic boot When the DC voltage is correctly connected, the inverter can be
automatically turned on after being connected to the mains power.
Conversion Time
(AC / DC)
?8ms
Conversion Time
(DC / AC)
?6ms
overload
protection
100% load 1 min, 150%10s: hardware reseter starts
short-circuit
protection
Software protection: Rester starts
Overtemperature
protection
The radiator stops charging after the temperature is greater than 90
degrees for 5 seconds, and the charging resumes after the temperature is
less than 70 degrees.
Overcharge
protection
Charging and protection according to the lead-acid battery
protection battery specifications.
Fan operation Controlled by each temperature sensor

Rated output power (W): 10000W
Rated output voltage (V): 220Vac
Rated output frequency (Hz): 50/60+ 1Hz
Output voltage range: 2203%

PLEASE CLICK BELOW TO VIEW OR DOWNLOAD THE PRODUCT SHEET

96V10KW inverter Specification

model 96V /10KW
Output rated
power
10000W
cell voltage DC 96
Battery voltage
range
80-128V
Battery type Solar deep cycle lead-acid battery, lithium battery can be setaccording to the battery parameters
AC charging
voltage
115V
Input voltage
waveform
Municipal s or connected generator
Rated input
voltage
220Vac 50/60HZ
Low voltage
switching point
175 + 5 Vac transferred into inverter mode
Low pressure
recovery point
170+ 5 Vac was transferred to the mains electricity modeHigh voltage
switching point
270+ 5 Vac transferred to inverter mode
High pressure
recovery point
265 + 5 Vac was transferred to the mains mode output frequency 50/601%
Rated input
frequency
50Hz /60 Hz 5%
Output voltage
waveform
Consistent with the input voltage waveform.
Power efficiency >85-87%
Charging method PW M
charging current 0A, 5A, 10A, 15A, 20A, 25A, 30A (factory setting 20A)
Automatic boot When the DC voltage is correctly connected, the inverter can be automatically turned on after being connected to the mains power.Conversion Time
(AC / DC)
8ms
Conversion Time
(DC / AC)
6ms
overload
protection
100% load 1 min, 150%10s: hardware reseter starts
short-circuit
protection
Software protection: Rester starts
Overtemperature
protection
The radiator stops charging after the temperature is greater than 90 degrees for 5 seconds, and the charging resumes after the temperature is less than 70 degrees.
Overcharge
protection
Charging and protection according to the lead-acid battery protection battery specifications.
Fan operation is Controlled by each temperature sensor.
Rated output
power (W)
10000W
Rated output
voltage (V)
220Vac
Rated output
frequency (Hz)
50/60+ 1Hz
Output voltage
range
2203%
96V
productiveness More than 85%
Output waveform
distortion
3%
peak factor 3:1
Load
applicability
Suitable for various loads
overload
protection
100% -120% load, alarm, protection after 1 minute./ 120% -150% load, alarm, protectionafter 30 seconds./ Greater than 150% load,alarm, and protection after 3 seconds.
short-circuit
protection
Use software detection protection, turn off the output, and automatically shut down after10 seconds.
Battery
undervoltage
alarm point
Single-section battery: 94V
Battery
undervoltage
protection point
Single-section battery: 90V
Overtemperature
protection
The radiator temperature is greater than 90, with over-temperature protection after 5 seconds.
Fan operation is Controlled by each temperature sensor.
switching mode Switch manually on the operator panel.
run mode
When the inverter works, if the output load is less than 5% of the rated load, the inverter turns off the output and is in the standby state. After 10 seconds, the inverter restarts and checks the load status. If the output load is greater than 10% of the rated load, the inverter will automatically turn on. If, still <5%.
Switch button Control the inverter switch for 2 seconds.
Smuffler
extinction key
Function button: "funct", short press to eliminate sound extinction, and then press to restore.
Energy-saving
mode button
Control the inverter to switch between normal or energy-saving modes.
Charging current
button
Select the different charging currents.
Output voltage
display
The number shows the AC output voltage of the current inverter.
Input voltage
display
The number shows the AC input voltage of the current inverter.
The output frequency
is shown
The number shows the AC output frequency of the current inverter.
The mains mode is
shown
The mains icon lights up and displays the mains input voltage
Inverse mode is
shown
Inverter icon lighting and display inverter output voltage + LED (yellow light)Battery level
display
The battery energy display bar is bright or out according to the battery power ratio. Load volume is
shown
The load display bar is bright or out in proportion to the load ratio.
Photovoltaic
charging mode
display
Pv icon to light up and display the PV input voltage current or power + LED (greenlight)Switch alarm The buzzer rings once every 2.2 seconds and calls for 1 second.
Battery
undervoltage
alarm
The buzzer rings once every 0.8 seconds and calls for 0.5 seconds.
Battery
under voltage
protection alarm
The buzzer rang continuously for 10s.
Battery
overvoltage alarm
The buzzer rings once every 2.2 seconds and c...